How To Add An Inline Fuse Into A Switch

Steps Download Commodity

one

Decide where you lot want to place your switch. More often than not wall switches are on the right-hand side, a few anxiety/metres past the door opening. Get around your firm and measure the height of other switches. 60" or 1.5m from the flooring is common.
2

Always turn off the ability to the fixture. If there are other people in the domicile, always tell them that you have turned off the power, or leave a note on the breaker/fuse box then someone doesn't accidentally plough it.^[1] ^[2]

Advertising
iii

Measure the distance from your fixture to the location of your new switch...e'er add an extra 12" or 30 centimeter (xi.viii in) to your measurement - it'southward always better to take too much electrical wire than not plenty.
iv

Cheque your fixture with a power tester to ensure that there is no power. Remove the black (or "hot") wire simply. Leave the white (or "neutral") and whatsoever ground (light-green or bare) wires on the fixture.^[iii]
5

Strip ii"/5 centimeter (ii.0 in) of the plastic sheathing from the end of the blackness and white wires.
6

Connect the black wire from the electrical cable with the black wire you only removed from your fixture. Ever use screw-on wire connectors..never use electrical record. Ensure that the connexion is tight.^[4]
7

Using a black marking, "re-code" the white wire from your electrical cable to black. Mark on the plastic sheathing with a permanent marker and then that anyone will know this is now a "hot" wire.^[5]
eight

Connect your re-coded "hot" wire to the fixture. You should at present take a white and re-coded black wire on your fixture.
9

At your new wall switch, pull all the wires through the dorsum of the electrical box. Strip black and white wires as in step 5. Connect the ground wire to the electrical box itself (there should be a spiral at the dorsum or side of the box).
x

You will need to re-code the white wire as a "hot" wire with a marking, as in pace 7. ^[6]
xi

Screw the black wire to the acme screw on your switch. This will be the elevation of your switch.
12

Spiral your newly re-coded second "hot" wire (white) to the bottom spiral. Ensure that both screws are secure and screw the switch into the electrical box. Do non adhere the cover until you check that everything functions correctly
thirteen

Picture show the switch to the "off" position, then turn on ability to the fixture.
14

Exam that your new switch works. If it does not, double check that you have not turned off the fixture from the chain/string.
15

You lot should e'er leave the light"on" at the chain/cord in order to have full command from the wall switch. You can yet use the concatenation, still this defeats the purpose of having a wall switch.
16

Provided everything works, y'all can close upwardly your light fixture and adhere a switch plate comprehend.

Advert

Add New Question

Question

How tin can I add a pull cord to overhead lighting?

You will have to replace the existing fixture with one that includes a pull cord.
Question

I replaced an old outlet from two prong to a 3 prong. I replaced the wires exactly haw information technology was on the one-time outlet, only my tester reads "hot/neutral reversed." How do I set up this?

Daverwaterloo

Community Answer

The new outlet may be in a different configuration from the former 1. New outlets have a left side that has a wider slot than the right side. The wider (left) slot is the neutral (white), while the narrower (right) side is the hot wire (black). Generally the hot side has a brass screw and the neutral side has a silverish screw. You'll need to opposite the wires on the back of the outlet.
Question

The overhead light in my dining room does not plough on after adding new calorie-free bulbs. How do I diagnose where the problem is?

Daverwaterloo

Community Answer

Will it turn on if you remove and/or replace the new bulbs? If then, you just take a defective bulb. If not, there may exist a brusk somewhere in the circuit. To diagnose this, remove the calorie-free switch and ensure all the connections are tight and not touching other wires or the electric box. If the switch is okay, bank check the calorie-free fixture that all the wiring is attached securely and not touching other wires.
Question

Is a new lite switch necessary?

Daverwaterloo

Community Answer

Not if y'all don't listen manually turning the light on and off direct at the fixture. Most people notice it easier and more convenient if they tin switch on a ceiling light fixture from a wall switch, especially at night.
Question

The fixture is looped to some other outlet. How do I add the switch without causing the outlet to be switched besides?

Daverwaterloo

Community Answer

Are you sure it is looped to an outlet, not another light fixture? Nearly homes are wired with the wall outlets on split circuits from lighting. If this is the case, you can't add a switch without switching the outlet likewise.
Question

I wired the new switch using the aforementioned color wires and now the low-cal just stays on. What did I do wrong?

Turn off the low-cal with the chain. Now you tin plough the light on or off with the wall switch.

Inquire a Question

200 characters left

Include your email address to get a bulletin when this question is answered.

Submit

Video

To attach a wire to a spiral, curve the bare wire to the left and slip information technology over the screw. When you tighten the screw, information technology will pull the wire down.
An electric tester is a good addition to whatever toolbox. They are inexpensive and can be bought at any home improvement/hardware store. Attach one probe to each wire...if the tester glows..the line is "hot", if not, the power has been turned off.
Before you attach wires with a spiral-on connector, twist the wires together with pliers.
Needle-nosed pliers and a wire stripper are handy tools to have in your toolbox for doing any electrical work. They are also inexpensive and will salvage you time and let you work "like a pro".
Make sure you lot e'er use the proper connector on the electric box to secure the wires in place. With the connector in identify, feed the wires through and secure them with attached clench.

Advert

Ensure that it is legal in your state/state to do your own electric work. If you are at all unsure, get a licensed electrician to do any electrical work in your home.
Always do any electrical work carefully and neatly. Double check all connections are tight.

Advertising